Enabling NIC Multi-Queue

Scenarios

With the increase of network I/O bandwidth, single-core CPUs face bottlenecks in handling network interrupts. NIC multi-queue assigns interrupts to different CPUs for higher packets per second (PPS) and bandwidth.

The ECS described in this section is assumed to comply with the requirements on specifications and virtualization type.

Support of NIC Multi-Queue

NIC multi-queue can be enabled on an ECS only when the ECS specifications, virtualization type, and image OS meet the requirements described in this section.

  • For details about the ECS specifications that support NIC multi-queue, see ECS Specifications.

    Note

    If the number of NIC queues is greater than 1, NIC multi-queue is supported.

  • The virtualization type must be KVM.

  • The Linux public images listed in Table 2 support NIC multi-queue.

    Note

    • Windows public images have not supported NIC multi-queue. If you enable NIC multi-queue in a Windows public image, starting an ECS created using such an image may be slow.

    • It is a good practice to upgrade the kernel version of the Linux ECS to 2.6.35 or later. Otherwise, NIC multi-queue is not supported.

      Run the uname -r command to obtain the kernel version. If the kernel version is earlier than 2.6.35, contact technical support to upgrade the kernel.

Table 1 Support of NIC multi-queue for Linux ECSs

Image

Support of NIC Multi-Queue

NIC Multi-Queue Enabled by Default

Ubuntu 14.04/16.04/18.04/20.04 server 64bit

Yes

Yes

OpenSUSE 42.2/15.* 64bit

Yes

Yes

SUSE Enterprise 12 SP1/SP2 64bit

Yes

Yes

CentOS 6.8/6.9/7.*/8.* 64bit

Yes

Yes

Debian 8.0.0/8.8.0/8.9.0/9.0.0/10.0.0/10.2.0 64bit

Yes

Yes

Fedora 24/25/30 64bit

Yes

Yes

EulerOS 2.2/2.3/2.5 64bit

Yes

Yes

Table 2 Support of NIC multi-queue for KVM ECSs

OS

Image

Status

Windows

Windows Server 2008 Web R2 64-bit

Supported using private images

Windows Server 2008 R2 Standard/DataCenter/Enterprise 64bit

Supported using private images

Windows Server 2012 R2 Standard/DataCenter 64bit

Supported using private images

Windows Server 2016 Standard/DataCenter 64bit

Supported using private images

Linux

Ubuntu 14.04/16.04 server 64bit

Supported

OpenSUSE 42.2 64bit

Supported

SUSE Enterprise 12 SP1/SP2 64bit

Supported

CentOS 6.8/6.9/7.0/7.1/7.2/7.3/7.4/7.5/7.6 64bit

Supported

Debian 8.0.0/8.8.0/8.9.0/9.0.0 64bit

Supported

Fedora 24/25 64bit

Supported

EulerOS 2.2 64bit

Supported

Importing the External Image File to the IMS Console

For details, see "Registering an Image File as a Private Image" in Image Management Service User Guide.

Setting NIC Multi-Queue for the Image

Windows OSs have not commercially supported NIC multi-queue. If you enable NIC multi-queue in a Windows image, starting an ECS created using such an image may be slow.

Use one of the following methods to set the NIC multi-queue attribute:

Method 1:

  1. Log in to the management console.

  2. Under Computing, click Image Management Service.

  3. Click the Private Images tab, locate the row containing the target image, click Modify in the Operation column.

  4. Set the NIC multi-queue attribute of the image.

Method 2:

  1. Log in to the management console.

  2. Under Computing, click Image Management Service.

  3. Click the Private Images tab. In the image list, click the name of the target image to switch to the page providing details about the image.

  4. Click Modify in the upper right corner. In the displayed Modify Image dialog box, set the NIC multi-queue attribute.

Method 3: Add hw_vif_multiqueue_enabled to an image through the API.

  1. For instructions about how to obtain the token, see Token Authentication.

  2. For instructions about how to call an API to update image information, see "Updating Image Information (Native OpenStack API)" in Image Management Service API Reference.

  3. Add X-Auth-Token to the request header.

    The value of X-Auth-Token is the token obtained in step 1.

  4. Add Content-Type to the request header.

    The value of Content-Type is application/openstack-images-v2.1-json-patch.

    The request URI is in the following format:

    PATCH /v2/images/{image_id}

    The request body is as follows:

    [
             {
              "op":"add",
              "path":"/hw_vif_multiqueue_enabled",
              "value": "true"
             }
     ]
    

    Figure 1 shows an example request body for modifying the NIC multi-queue attribute.

    **Figure 1** Example request body

    Figure 1 Example request body

Creating an ECS Using a Private Image

Create an ECS using a registered private image. For details, see Creating an ECS. Note the following when setting the parameters:

  • Region: Select the region where the private image is located.

  • Image: Select Private image and then the desired image from the drop-down list.

Enabling NIC Multi-Queue

KVM Windows ECSs use private images to support NIC multi-queue. For details, see "How Do I Set NIC Multi-queue Feature of an Image?" in Image Management Service User Guide.

This section uses a Linux ECS running CentOS 7.4 as an example to describe how to enable NIC multi-queue.

  1. Enable NIC multi-queue.

    1. Log in to the ECS.

    2. Run the following command to obtain the number of queues supported by the NIC and the number of queues with NIC multi-queue enabled:

      ethtool -l NIC

    3. Run the following command to configure the number of queues used by the NIC:

      ethtool -L NIC combined Number of queues

    An example is provided as follows:

    [root@localhost ~]# ethtool -l eth0  #View the number of queues used by NIC eth0.
    Channel parameters for eth0:
    Pre-set maximums:
    RX:               0
    TX:               0
    Other:                  0
    Combined: 4  #Indicates that a maximum of four queues can be enabled for the NIC.
    Current hardware settings:
    RX:               0
    TX:               0
    Other:                  0
    Combined: 1 #Indicates that one queue has been enabled.
    
    [root@localhost ~]# ethtool -L eth0 combined 4 #Enable four queues on NIC eth0.
    
  2. (Optional) Enable irqbalance so that the system automatically allocates NIC interrupts on multiple vCPUs.

    1. Run the following command to enable irqbalance:

      service irqbalance start

    2. Run the following command to view the irqbalance status:

      service irqbalance status

      If the Active value in the command output contains active (running), irqbalance has been enabled.

      **Figure 2** Enabled irqbalance

      Figure 2 Enabled irqbalance

  3. (Optional) Enable interrupt binding.

    Enabling irqbalance allows the system to automatically allocate NIC interrupts, improving network performance. If the improved network performance still fails to meet your requirements, manually configure interrupt affinity on the ECS.

    To do so, perform the following operations:

    Configure the following script so that one ECS vCPU serves the interrupt requests initialized by one queue. One queue corresponds to one interrupt, and one interrupt binds to one vCPU.

    #!/bin/bash
    service irqbalance stop
    
    eth_dirs=$(ls -d /sys/class/net/eth*)
    if [ $? -ne 0 ];then
        echo "Failed to find eth*  , sleep 30" >> $ecs_network_log
        sleep 30
        eth_dirs=$(ls -d /sys/class/net/eth*)
    fi
    
    for eth in $eth_dirs
    do
        cur_eth=$(basename $eth)
        cpu_count=`cat /proc/cpuinfo| grep "processor"| wc -l`
        virtio_name=$(ls -l /sys/class/net/"$cur_eth"/device/driver/ | grep pci |awk {'print $9'})
    
        affinity_cpu=0
        virtio_input="$virtio_name""-input"
        irqs_in=$(grep "$virtio_input" /proc/interrupts | awk -F ":" '{print $1}')
        for irq in ${irqs_in[*]}
        do
            echo $((affinity_cpu%cpu_count)) > /proc/irq/"$irq"/smp_affinity_list
            affinity_cpu=$[affinity_cpu+2]
        done
    
        affinity_cpu=1
        virtio_output="$virtio_name""-output"
        irqs_out=$(grep "$virtio_output" /proc/interrupts | awk -F ":" '{print $1}')
        for irq in ${irqs_out[*]}
        do
            echo $((affinity_cpu%cpu_count)) > /proc/irq/"$irq"/smp_affinity_list
            affinity_cpu=$[affinity_cpu+2]
        done
    done
    
  4. (Optional) Enable XPS and RPS.

    XPS allows the system with NIC multi-queue enabled to select a queue by vCPU when sending a data packet.

    #!/bin/bash
    # enable XPS feature
    cpu_count=$(grep -c processor /proc/cpuinfo)
    dec2hex(){
      echo $(printf "%x" $1)
    }
    eth_dirs=$(ls -d /sys/class/net/eth*)
    if [ $? -ne 0 ];then
        echo "Failed to find eth* , sleep 30" >> $ecs_network_log
        sleep 30
        eth_dirs=$(ls -d /sys/class/net/eth*)
    fi
    for eth in $eth_dirs
    do
        cpu_id=1
        cur_eth=$(basename $eth)
        cur_q_num=$(ethtool -l $cur_eth | grep -iA5 current | grep -i combined | awk {'print $2'})
        for((i=0;i<cur_q_num;i++))
        do
            if [ $i -eq $cpu_count ];then
                cpu_id=1
            fi
            xps_file="/sys/class/net/${cur_eth}/queues/tx-$i/xps_cpus"
            rps_file="/sys/class/net/${cur_eth}/queues/rx-$i/rps_cpus"
            cpuset=$(dec2hex "$cpu_id")
            echo $cpuset > $xps_file
            echo $cpuset > $rps_file
            let cpu_id=cpu_id*2
        done
    done